Most people want to access the Internet from any room in the house/office and maybe even in the garden or summer house.
Although most people will want extended Wireless (Wi-Fi) access we will also look at how to extend both wired and wireless access.
If we start with a basic home network consisting of a single Wireless access point (WAP) that is part of the Wireless router as described in building a home network and shown below:
The home router is the hub of the network as it connects your home network to the Internet.
This basic configuration can be extended to provide both wired and Wireless access using a variety of methods and illustrated in the network diagram below:
Extending Wi-Fi Access
Before you go to the trouble of extending a network it is a good idea to try an get a better signal by relocating the router/Wireless access point if possible.
If we assume that the present WAP (Wireless Access Point) covers area 1 but not area 2 and our task is to extend the Wi-Fi network to cover area 2.
To extend the Wi-Fi coverage to area 2 we will need a second WAP (Wireless access point), and this second access point will need to connect to the WAP in Area 1.
There are three methods available for connecting the Wireless Access Points ( WAPs) together. They are:
- Use a WAP connected to the hub on network 1 using an Ethernet cable.
- Use a WAP connected to the hub on network 1 using Homeplug adapters.
- Connect with Wi-FI using a Wi-Fi range extender or repeater.
Using a Wireless Repeater or Range Extender
This is probably the quickest and easiest method and according to a recent survey used by over 20% of US households.
It is also the slowest and the most error prone method method.
Note You will hear the terms repeater,range extender and booster used but they are generally describing the same thing.
A Wireless Repeater takes a wireless signal and then re-broadcasts it.
This means that the repeater must be in range of the original Wireless signal.
It also usually means that the throughput is halved. However some repeaters using different bands i.e. they could use the 5Ghz band for the connection to the WAP and the 2.5 Ghz band for connecting to devices.
The repeater creates a second Wireless network which usually has a different SSID than the original network.
Because wireless devices on network 2 must go through two wireless hops this connection method is much slower than using an Ethernet extension cable or homeplug adaptors.
Extending a Wired Network
To extend a wired network you will need an Ethernet Switch.
You use a port on the Home router to connect to the remote switch using either:
- A long UTP cable
- Homeplug adapters.
This is illustrated in the main network diagram above.
Using an Ethernet Cable
You can purchase UTP connection cables of various lengths which means that you don’t need to create your own cables.
You should note that the maximum cable distance between network devices is 100m.
However you will need to run the cable between rooms which usually involves drilling holes etc.
Although this is a very low cost method it is usually not the easiest. It does however provide the fastest and most reliable connection.
Using Homeplug Adapters
Homeplug adaptors are the more flexible option than straight wiring as they can easily add network connectivity to any room that has a power outlet.
They work by using the home electrical wiring to carry the Ethernet signal between rooms.
Homeplug adapters can be used to extend both a wired and wireless network .
Generally they work in pairs but you can use more than 2 on a network. They plug into the mains socket and usually provide an Ethernet connection on each end.
You simply plug the Ethernet cables into the adapters at each end.
They can also come with built in wireless access points so that you don’t need an additional wireless access points to extend the wireless network.
Homeplug adapters with built in Wireless access points tend to be a little more expensive than standard Ethernet ones but are very convenient. Ref– Powerline networking guide
Network SSIDs (Network Name)
Regardless of how you extend the network you will likely end up with two or more wireless networks.
You can configure these networks to use the same broadcast SSID so that they appear to be a single network but this can cause problems with some devices.
On my network I use different SSIDs but the same password.
- ASUS FAQ –Why is the wireless network name (SSID) of range extender different from my Wi-Fi router?
- What happens if my neighbour sets his wifi SSID the same as mine?
The Screen shot below shows my home network with multiple Access points and Network IDs.
Extending Ethernet Ports
If you are short of Ethernet ports in any location you can use a second Ethernet switch connected to the other Ethernet switch as shown in the diagram below.
Note: It isn’t important which port you use.
Extending Ethernet Cable
You can extend an Ethernet cable using an Ethernet coupler like the one below.
You can also get a cable with female connection as shown below
The connecting cable category (5,6,7) should match or be better than the existing cable female socket to match your cable.
Extending with an Ethernet Repeater
The maximum cable distance between networking devices on an Ethernet network is 100m.
However this can be extending to approx 300m by using an Ethernet repeater/extender. Most of the ones available today appear to be PoE repeaters.
With PoE devices you can connect remote devices like IP cameras without the need for installing a separate power supply. See PoE for beginners
Extending Using a Wireless Bridge
This is an ideal method of extending your network to an out building without having to run Ethernet cables.
It uses a line of site wireless link between two wireless bridges. At the remote end the bridge connects to the remote network.
Take a look at the TP LInk NE300 (affiliate link)
If you are worried whether or not it will work for you take a look at the reviews. I have taken a screen shot of a few below:
Wi-FI Mesh Networks
These are also relatively new systems that aim to provide Wi-Fi access in larger homes.
They comprise 2 or more Wi-Fi nodes that work together to offer a single Wi-Fi network (same SSID).
Wireless electrical power sockets are a new introduction to the market and function as wireless repeaters.
They are convenient because they don’t consume a electrical power socket. Here is a picture of a UK socket.
Common Questions and Answers
Q-Can I use an old Wi-Fi router to extend my network.?
A- Yes but it will need to function solely as an access point. This PCworld article describes how.
Personally I’m not keen on this as the setup is convoluted, easy to get wrong, and it is not possible on all routers. Wi-Fi access points are cheap it is easier to get a new access point.
Q-Can I extend my home network with another router?
A- Yes but a router is the wrong choice on a home network unless you want two separate networks. A network switch is the better choice and the easiest. Using a router would involve setup that would require a very good knowledge of networking, and sub netting in particular. See 2 Routers on a home network
Network Extension -Case Studies
I often get asked questions via the ask Steve page and thought it would be useful if I included a few of the questions and answers here as they might be applicable to your situation. I have removed names to protect the identity.
Case Study 1 – Bad Wi-Fi
Question- Hi Steve, I have just moved into an old house in a rural location. Because of very poor WIFI over the land line and poor router signal coverage in the house (thick walls etc), the previous owner installed an EE SIMM based router linked by CAT5 to a ceiling mounted EnGenius EAP150. Apparently this has improved things (download speeds of 15 MBPS and 3.3 MBPS for uploads when close to the EAP), but the the signal does not go very far and dropped connections and lack of connection are a frequent pain. Using Netflix and a couple of mobile phones seems to cause loss of signal very easily, I guess this is a capacity issue? Can you make any suggestions on how to address these problems please? E.G Can I use signal boosters around the house to strengthen the EAP signal? Do I need a better WAP/EAP device? Are there other alternatives?
Answer – I would try using homeplug adapters you can get them with Wi-FI access points. Get a pair and put one next to your router and move the other wi-fi homeplug around the rooms to make sure it works as there could potentially be wiring problems. If that works ok you can always add additional adapters.
Reply – Many thanks for your suggestion. I bought some TP-Link power-line adapters and they work really well.
Related Tutorials and Useful Resources:
- Wi_fi and Wireless networks for Beginners
- Setting up a Homeplug Power Line network
- Power Over Ethernet (POE)
- wifi-booster-repeater-extender- What’s the difference